DNA Sequencing Service

From Wikipedia

While the chemical sequencing method of Maxam and Gilbert, and the plus-minus method of Sanger and Coulson were orders of magnitude faster than previous methods, the chain-terminator method developed by Sanger was even more efficient, and rapidly became the method of choice. The Maxam-Gilbert technique requires the use of highly toxic chemicals, and large amounts of radiolabeled DNA, whereas the chain-terminator method uses fewer toxic chemicals and lower amounts of radioactivity. The key principle of the Sanger method was the use of dideoxynucleotides triphosphates (ddNTPs) as DNA chain terminators.

Figure: Part of a radioactively labelled sequencing gel 

The classical chain-termination or Sanger method requires a single-stranded DNA template, a DNA primer, a DNA polymerase, radioactively or fluorescently labeled nucleotides, and modified nucleotides that terminate DNA strand elongation. The DNA sample is divided into four separate sequencing reactions, containing the four standard deoxynucleotides (dATP, dGTP, dCTP and dTTP) and the DNA polymerase. To each reaction is added only one of the four dideoxynucleotides (ddATP, ddGTP, ddCTP, or ddTTP). These dideoxynucleotides are the chain-terminating nucleotides, lacking a 3′-OH group required for the formation of a phosphodiester bond between two nucleotides during DNA strand elongation. Incorporation of a dideoxynucleotide into the nascent (elongating) DNA strand therefore terminates DNA strand extension, resulting in various DNA fragments of varying length. The dideoxynucleotides are added at lower concentration than the standard deoxynucleotides to allow strand elongation sufficient for sequence analysis.

Figure: DNA fragments can be labeled by using a radioactive or fluorescent tag on the primer (1), in the new DNA strand with a labeled dNTP, or with a labeled ddNTP.
The newly synthesized and labeled DNA fragments are heat denatured, and separated by size (with a resolution of just one nucleotide) by gel electrophoresis on a denaturing polyacrylamide-urea gel. Each of the four DNA synthesis reactions is run in one of four individual lanes (lanes A, T, G, C); the DNA bands are then visualized by autoradiography or UV light, and the DNA sequence can be directly read off the X-ray film or gel image. In the image on the right, X-ray film was exposed to the gel, and the dark bands correspond to DNA fragments of different lengths. A dark band in a lane indicates a DNA fragment that is the result of chain termination after incorporation of a dideoxynucleotide (ddATP, ddGTP, ddCTP, or ddTTP). The terminal nucleotide base can be identified according to which dideoxynucleotide was added in the reaction giving that band. The relative positions of the different bands among the four lanes are then used to read (from bottom to top) the DNA sequence as indicated.

There are some technical variations of chain-termination sequencing. In one method, the DNA fragments are tagged with nucleotides containing radioactive phosphorus for radiolabelling. Alternatively, a primer labeled at the 5’ end with a fluorescent dye is used for the tagging. Four separate reactions are still required, but DNA fragments with dye labels can be read using an optical system, facilitating faster and more economical analysis and automation. This approach is known as ‘dye-primer sequencing’. The later development by L Hood and coworkers[6][7] of fluorescently labeled ddNTPs and primers set the stage for automated, high-throughput DNA sequencing.

The different chain-termination methods have greatly simplified the amount of work and planning needed for DNA sequencing. For example, the chain-termination-based “Sequenase” kit from USB Biochemicals contains most of the reagents needed for sequencing, prealiquoted and ready to use. Some sequencing problems can occur with the Sanger Method, such as non-specific binding of the primer to the DNA, affecting accurate read out of the DNA sequence. In addition, secondary structures within the DNA template, or contaminating RNA randomly priming at the DNA template can also affect the fidelity of the obtained sequence. Other contaminants affecting the reaction may consist of extraneous DNA or inhibitors of the DNA polymerase.

Dye-terminator sequencing

An alternative to primer labelling is labelling of the chain terminators, a method commonly called ‘dye-terminator sequencing’. The major advantage of this method is that the sequencing can be performed in a single reaction, rather than four reactions as in the labelled-primer method. In dye-terminator sequencing, each of the four dideoxynucleotide chain terminators is labelled with a different fluorescent dye, each fluorescing at a different wavelength. This method is attractive because of its greater expediency and speed and is now the mainstay in automated sequencing with computer-controlled sequence analyzers (see below). Its potential limitations include dye effects due to differences in the incorporation of the dye-labelled chain terminators into the DNA fragment, resulting in unequal peak heights and shapes in the electronic DNA sequence trace chromatogram after capillary electrophoresis (see figure to the right). This problem has largely been overcome with the introduction of new DNA polymerase enzyme systems and dyes that minimize incorporation variability, as well as methods for eliminating “dye blobs”, caused by certain chemical characteristics of the dyes that can result in artifacts in DNA sequence traces. The dye-terminator sequencing method, along with automated high-throughput DNA sequence analyzers, is now being used for the vast majority of sequencing projects, as it is both easier to perform and lower in cost than most previous sequencing methods.

Automation and sample preparation

Modern automated DNA sequencing instruments (DNA sequencers) can sequence up to 384 fluorescently labelled samples in a single batch (run) and perform as many as 24 runs a day. However, automated DNA sequencers carry out only DNA size separation by capillary electrophoresis, detection and recording of dye fluorescence, and data output as fluorescent peak trace chromatograms. Sequencing reactions by thermocycling, cleanup and re-suspension in a buffer solution before loading onto the sequencer are performed separately.

Figure: Sequence ladder by radioactive sequencing compared to fluorescent peaks

Figure: View of the start of an example dye-terminator read

DNA Sequencing on Wikipedia